MCQs – General Science – Significant Figures, Measurement Errors, Accuracy and Precision

Significant Figures, Measurement Errors, Accuracy and Precision: 50 MCQs

1 Significant figures in a measured value indicate:

(a) Only the number of digits before the decimal point
(b) The meaningful digits justified by the measurement
(c) The number of instruments used
(d) None of these

2 How many significant figures are present in 245.6?

(a) Two
(b) Three
(c) Four
(d) None of these

3 How many significant figures are present in 0.00450?

(a) Three
(b) Two
(c) Four
(d) None of these

4 How many significant figures are present in 300.0?

(a) One
(b) Two
(c) Three
(d) Four

5 Which zeros are generally not significant in a decimal number?

(a) Zeros between non-zero digits
(b) Leading zeros before the first non-zero digit
(c) Trailing zeros in a properly written decimal measurement
(d) None of these

6 How many significant figures are present in 7.020?

(a) Two
(b) Three
(c) Four
(d) None of these

7 What is the correct result of adding 12.11, 18.0 and 1.013 according to significant-figure rules?

(a) 31.1
(b) 31.123
(c) 31.12
(d) None of these

8 When multiplying measured quantities, the result should generally contain:

(a) The greatest number of decimal places
(b) Exactly two significant figures
(c) The same number of digits as the largest factor
(d) The same number of significant figures as the factor with the fewest significant figures

9 What is the result of multiplying 2.5 by 3.42, expressed using appropriate significant figures?

(a) 8.550
(b) 8.6
(c) 8.55
(d) None of these

10 What is the result of dividing 15.0 by 4.0 using significant-figure rules?

(a) 3.750
(b) 3.8
(c) 3.75
(d) None of these

11 Scientific notation is particularly useful for:

(a) Expressing very large or very small numbers conveniently
(b) Removing measurement uncertainty
(c) Changing the physical value of a quantity
(d) None of these

12 Which is the correct scientific notation for 0.000072?

(a) (72 \times 10^{-6})
(b) (7.2 \times 10^{-4})
(c) (0.72 \times 10^{-4})
(d) (7.2 \times 10^{-5})

13 Which is the correct scientific notation for 5,600,000?

(a) (56 \times 10^5)
(b) (5.6 \times 10^6)
(c) (0.56 \times 10^7)
(d) None of these

14 Accuracy refers to:

(a) The number of decimal places in a result
(b) The repeatability of measurements
(c) The closeness of a measured value to the true or accepted value
(d) None of these

15 Precision refers to:

(a) The closeness of repeated measurements to one another
(b) The closeness of a measurement to the true value only
(c) The size of the measuring instrument
(d) None of these

16 A set of measurements can be precise but inaccurate when:

(a) All measurements are widely scattered
(b) Every measurement equals the accepted value
(c) The instrument has no systematic error
(d) Measurements are closely grouped but far from the accepted value

17 Which type of error causes measurements to deviate consistently in one direction?

(a) Random error
(b) Systematic error
(c) Human reading variation only
(d) None of these

18 Random errors are generally caused by:

(a) A permanently miscalibrated instrument
(b) An incorrect unit conversion
(c) Unpredictable variations in measurement conditions
(d) None of these

19 Which error can be reduced by taking repeated measurements and calculating their mean?

(a) Random error
(b) A constant calibration error
(c) A fixed zero error
(d) None of these

20 A zero error occurs when:

(a) An instrument has no scale
(b) A measurement is repeated
(c) The measured object has zero mass
(d) An instrument shows a non-zero reading when the actual quantity is zero

21 Calibration of a measuring instrument involves:

(a) Increasing its physical size
(b) Comparing its readings with known standards and adjusting or documenting deviations
(c) Removing all uncertainty from measurement
(d) None of these

22 Which of the following is an example of a systematic measurement error?

(a) Random fluctuations in room temperature
(b) Slight differences in repeated human reaction times
(c) A balance that consistently reads 2 g too high
(d) None of these

23 The absolute error is the:

(a) Magnitude of the difference between a measured value and the accepted value
(b) Ratio of error to the accepted value
(c) Sum of all repeated measurements
(d) None of these

24 Relative error is calculated by:

(a) Multiplying absolute error by the measured value
(b) Adding absolute error to the true value
(c) Subtracting the measured value from zero
(d) Dividing absolute error by the accepted or reference value

25 Percentage error is obtained by:

(a) Dividing the measured value by 100
(b) Multiplying relative error by 100
(c) Adding the relative error to the true value
(d) None of these

26 A measured length is 9.8 cm while the accepted length is 10.0 cm. What is the absolute error?

(a) 0.02 cm
(b) 0.20 cm
(c) 2.0 cm
(d) None of these

27 A measured value is 48 while the accepted value is 50. What is the percentage error?

(a) 4%
(b) 2%
(c) 5%
(d) None of these

28 If the measured value is 98 and the accepted value is 100, the relative error is:

(a) 0.2
(b) 0.02%
(c) 2
(d) 0.02

29 Which term describes the uncertainty associated with the smallest scale division of an instrument?

(a) Systematic bias
(b) Instrument resolution
(c) Percentage error
(d) None of these

30 The least count of a measuring instrument is:

(a) Its maximum possible reading
(b) The total length of its scale
(c) The smallest value it can measure or resolve
(d) None of these

31 Which instrument generally provides a smaller least count for measuring small external diameters?

(a) Micrometer screw gauge
(b) Ordinary metre rule
(c) Measuring tape
(d) None of these

32 The uncertainty in a measurement is important because:

(a) It makes all measurements invalid
(b) It eliminates the need for calibration
(c) It proves that the measured value is incorrect
(d) It indicates the range within which the measured quantity is reasonably expected to lie

33 If repeated measurements are 10.1 cm, 10.2 cm and 10.0 cm, their arithmetic mean is:

(a) 10.2 cm
(b) 10.1 cm
(c) 10.3 cm
(d) None of these

34 Which of the following best describes reproducibility?

(a) Obtaining identical results from one instrument only
(b) Repeating the same calculation without changing data
(c) Obtaining consistent results under changed conditions, such as different laboratories or operators
(d) None of these

35 Which concept is most closely associated with repeatability?

(a) Agreement among repeated measurements under the same conditions
(b) Agreement with a theoretical prediction only
(c) The number of units in a measurement
(d) None of these

36 Which of the following can improve measurement accuracy?

(a) Ignoring calibration requirements
(b) Using a damaged instrument
(c) Recording readings selectively
(d) Using properly calibrated instruments and appropriate measurement procedures

37 Which statement about significant figures is correct?

(a) All zeros are always significant
(b) Exact counted quantities have unlimited significant figures for calculation purposes
(c) Every measured value must have exactly three significant figures
(d) None of these

38 In the value 6.004, how many significant figures are present?

(a) Two
(b) Three
(c) Four
(d) None of these

39 What is the result of rounding 8.746 to three significant figures?

(a) 8.75
(b) 8.74
(c) 8.70
(d) None of these

40 What is the result of rounding 0.006784 to two significant figures?

(a) 0.0067
(b) 0.0068
(c) 0.0070
(d) None of these

41 Which statistical measure is commonly used to describe the spread of data around the mean?

(a) Median
(b) Mode
(c) Standard deviation
(d) None of these

42 A smaller standard deviation generally indicates:

(a) Greater spread of observations
(b) Greater systematic error
(c) A larger sample mean in every case
(d) Less spread of observations around the mean

43 Which graph is commonly used to examine whether measurement errors are randomly distributed around zero?

(a) Residual plot
(b) Pie chart
(c) Population pyramid
(d) None of these

44 An outlier is:

(a) The average of all measurements
(b) A value that differs markedly from the general pattern of the data
(c) The smallest possible measurement
(d) None of these

45 Which approach is appropriate when an outlier is detected in an experiment?

(a) Delete it automatically
(b) Change it to match the mean
(c) Investigate its cause and apply justified criteria before deciding how to handle it
(d) None of these

46 Which type of uncertainty is evaluated using statistical analysis of repeated observations?

(a) Type A uncertainty
(b) Type B uncertainty
(c) Calibration traceability
(d) None of these

47 Type B evaluation of measurement uncertainty commonly uses:

(a) Repeated observations only
(b) Other information such as calibration certificates, specifications and reference data
(c) Random selection of results
(d) None of these

48 Measurement traceability refers to:

(a) Recording measurements without units
(b) Using any available instrument
(c) Avoiding reference standards
(d) An unbroken documented chain of calibrations linked to recognized standards

49 Which of the following best describes the relationship between accuracy and precision?

(a) They are distinct properties and a measurement can be precise without being accurate
(b) They always mean exactly the same thing
(c) Precision is independent of repeated measurements
(d) None of these

50 Why should measurement uncertainty be reported in scientific research?

(a) To make results appear less reliable
(b) To communicate the limitations and reliability of measured values
(c) To replace the measured result
(d) None of these

Answer Key

1 (b) The meaningful digits justified by the measurement
2 (c) Four
3 (a) Three
4 (d) Four
5 (b) Leading zeros before the first non-zero digit
6 (c) Four
7 (a) 31.1
8 (d) The same number of significant figures as the factor with the fewest significant figures
9 (b) 8.6
10 (c) 3.75
11 (a) Expressing very large or very small numbers conveniently
12 (d) (7.2 \times 10^{-5})
13 (b) (5.6 \times 10^6)
14 (c) The closeness of a measured value to the true or accepted value
15 (a) The closeness of repeated measurements to one another
16 (d) Measurements are closely grouped but far from the accepted value
17 (b) Systematic error
18 (c) Unpredictable variations in measurement conditions
19 (a) Random error
20 (d) An instrument shows a non-zero reading when the actual quantity is zero
21 (b) Comparing its readings with known standards and adjusting or documenting deviations
22 (c) A balance that consistently reads 2 g too high
23 (a) Magnitude of the difference between a measured value and the accepted value
24 (d) Dividing absolute error by the accepted or reference value
25 (b) Multiplying relative error by 100
26 (b) 0.20 cm
27 (a) 4%
28 (d) 0.02
29 (b) Instrument resolution
30 (c) The smallest value it can measure or resolve
31 (a) Micrometer screw gauge
32 (d) It indicates the range within which the measured quantity is reasonably expected to lie
33 (b) 10.1 cm
34 (c) Obtaining consistent results under changed conditions, such as different laboratories or operators
35 (a) Agreement among repeated measurements under the same conditions
36 (d) Using properly calibrated instruments and appropriate measurement procedures
37 (b) Exact counted quantities have unlimited significant figures for calculation purposes
38 (c) Four
39 (a) 8.75
40 (b) 0.0068
41 (c) Standard deviation
42 (d) Less spread of observations around the mean
43 (a) Residual plot
44 (b) A value that differs markedly from the general pattern of the data
45 (c) Investigate its cause and apply justified criteria before deciding how to handle it
46 (a) Type A uncertainty
47 (b) Other information such as calibration certificates, specifications and reference data
48 (d) An unbroken documented chain of calibrations linked to recognized standards
49 (a) They are distinct properties and a measurement can be precise without being accurate
50 (b) To communicate the limitations and reliability of measured values

 

3 Views