Table of Contents
Electric Current, Voltage and Resistance
1. Introduction
Electric current, voltage and resistance are three fundamental quantities in the study of electricity.
Electric current describes the rate at which electric charge flows through a conductor. Voltage represents the electric potential difference that can drive charge through a circuit. Resistance describes the opposition offered by a material or component to the flow of electric current.
These concepts are essential for understanding electrical circuits, household appliances, electronic devices, power generation and electrical energy consumption.
2. Electric Current
Electric current is the rate of flow of electric charge through a conductor or another medium.
It is represented by the symbol (I).
[
I=\frac{\Delta Q}{\Delta t}
]
Where:
- (I) = electric current
- (\Delta Q) = electric charge transferred
- (\Delta t) = time interval
For a steady current:
[
I=\frac{Q}{t}
]
The SI unit of electric current is the ampere (A).
One ampere is defined as the flow of one coulomb of charge per second.
[
1\ A=1\ C/s
]
Numerical Example
If (30\ C) of electric charge passes through a conductor in (10) seconds, calculate the current.
[
I=\frac{Q}{t}
]
[
I=\frac{30}{10}
]
[
\boxed{I=3\ A}
]
3. Conventional Current and Electron Flow
In metallic conductors, electric current is mainly carried by electrons.
Electrons have negative charge and move from the negative terminal towards the positive terminal of a source in the external circuit.
However, conventional current is defined as flowing in the direction that positive charges would move.
Therefore:
- Conventional current flows from positive to negative through the external circuit.
- Electron flow in a metal is opposite to conventional current.
The distinction is important when studying electrical circuits and electronic components.
In electrolytes, current is carried by positive and negative ions. In semiconductors, both electrons and holes contribute to conduction.
4. Types of Electric Current
4.1 Direct Current (DC)
Direct current flows in one direction.
Its magnitude may be constant or may vary with time, but its direction does not reverse.
Common sources include:
- Batteries
- Cells
- Solar photovoltaic systems
- DC power supplies
DC is widely used in electronic devices, computers and battery-powered equipment.
4.2 Alternating Current (AC)
Alternating current periodically changes direction.
In a typical sinusoidal AC supply, current and voltage vary periodically with time.
The frequency indicates the number of complete cycles per second.
The SI unit of frequency is hertz (Hz).
[
f=\frac{1}{T}
]
Where:
- (f) = frequency
- (T) = time period
Many electricity distribution systems use alternating current because its voltage can be changed efficiently using transformers.
5. Voltage or Potential Difference
Voltage is the electric potential difference between two points in a circuit.
It represents the change in electric potential energy per unit charge.
[
V=\frac{W}{Q}
]
Where:
- (V) = voltage
- (W) = work or energy transferred
- (Q) = charge
The SI unit of voltage is the volt (V).
[
1\ V=1\ J/C
]
A potential difference can drive electric charge through a circuit when a conducting path is available.
Numerical Example
If (60\ J) of energy is transferred when (10\ C) of charge moves between two points, calculate the potential difference.
[
V=\frac{W}{Q}
]
[
V=\frac{60}{10}
]
[
\boxed{V=6\ V}
]
6. Electromotive Force (EMF)
Electromotive force is the energy supplied by a source per unit charge passing through it.
It is represented by the symbol (\varepsilon).
[
\varepsilon=\frac{W}{Q}
]
Its SI unit is the volt.
Despite its name, electromotive force is not actually a mechanical force. It is an energy-per-unit-charge quantity.
A battery provides energy to charges through chemical reactions. Its EMF represents the energy supplied per unit charge under the specified conditions.
Difference Between EMF and Terminal Voltage
- EMF is the energy supplied per unit charge by a source.
- Terminal voltage is the potential difference measured across the terminals of a source.
When a battery supplies current, its terminal voltage may be lower than its EMF because of internal resistance.
For a source delivering current:
[
V=\varepsilon-Ir
]
Where:
- (V) = terminal voltage
- (\varepsilon) = EMF
- (I) = current
- (r) = internal resistance
7. Electrical Resistance
Resistance is the opposition offered by a material or electrical component to the flow of electric current.
It is represented by the symbol (R).
For an ohmic conductor under constant physical conditions:
[
R=\frac{V}{I}
]
The SI unit of resistance is the ohm ((\Omega)).
One ohm is the resistance of a conductor through which a current of one ampere flows when a potential difference of one volt is applied.
[
1\ \Omega=1\ V/A
]
7.1 Factors Affecting Resistance
The resistance of a uniform conductor depends on several factors.
1. Length
Resistance increases with the length of the conductor.
[
R\propto L
]
2. Cross-sectional Area
Resistance decreases as the cross-sectional area increases.
[
R\propto\frac{1}{A}
]
3. Material
Different materials have different electrical resistivities.
4. Temperature
The resistance of most metallic conductors increases as temperature rises. The behaviour of semiconductors and other materials may differ.
The combined relationship is:
[
R=\rho\frac{L}{A}
]
Where:
- (R) = resistance
- (\rho) = resistivity
- (L) = length
- (A) = cross-sectional area
8. Resistivity
Resistivity is an intrinsic property of a material that indicates how strongly it opposes the flow of electric current.
It is represented by the Greek letter (\rho).
[
\rho=\frac{RA}{L}
]
The SI unit of resistivity is ohm metre ((\Omega m)).
Unlike resistance, resistivity is a property of the material and does not directly depend on the dimensions of a uniform sample at a given temperature and physical condition.
Copper has relatively low resistivity, which makes it suitable for electrical wiring.
Rubber and glass have very high resistivity, making them useful insulating materials.
9. Conductance
Conductance measures how easily electric current flows through a component.
It is the reciprocal of resistance.
[
G=\frac{1}{R}
]
Where:
- (G) = conductance
- (R) = resistance
The SI unit of conductance is the siemens (S).
A component with high conductance has low resistance, while a component with low conductance has high resistance.
10. Electric Power
Electric power is the rate at which electrical energy is transferred or converted into another form of energy.
It is represented by (P).
[
P=\frac{W}{t}
]
For a DC circuit or a resistive element under suitable conditions:
[
P=VI
]
Using Ohm’s law, the following expressions can also be obtained:
[
P=I^2R
]
[
P=\frac{V^2}{R}
]
Where:
- (P) = power in watts (W)
- (V) = voltage in volts (V)
- (I) = current in amperes (A)
- (R) = resistance in ohms ((\Omega))
Numerical Example
An electric heater operates at (220\ V) and draws a current of (5\ A). Calculate its electrical power.
[
P=VI
]
[
P=220\times5
]
[
\boxed{P=1100\ W}
]
The heater has a power rating of (1.1\ kW).
For AC circuits, the simple product of RMS voltage and RMS current gives apparent power. Real power in a general AC circuit also depends on the power factor.
11. Electrical Energy
Electrical energy is the total amount of energy transferred or consumed by an electrical device over a period of time.
[
E=Pt
]
Since:
[
P=VI
]
Therefore:
[
E=VIt
]
The SI unit of electrical energy is the joule (J).
Commercial electricity consumption is commonly measured in kilowatt-hours (kWh).
[
1\ kWh=3.6\times10^6\ J
]
One kilowatt-hour is the energy consumed by a device operating at a power of one kilowatt for one hour.
Numerical Example
A 2 kW electric heater operates for 3 hours. Calculate the energy consumed.
[
E=Pt
]
[
E=2\times3
]
[
\boxed{E=6\ kWh}
]
In joules:
[
6\times3.6\times10^6
]
[
\boxed{E=21.6\times10^6\ J}
]
12. Measuring Electrical Quantities
12.1 Ammeter
An ammeter measures electric current.
It is connected in series with the component through which current is being measured.
An ideal ammeter has zero resistance so that it does not significantly alter the current in the circuit.
12.2 Voltmeter
A voltmeter measures potential difference between two points.
It is connected in parallel with the component.
An ideal voltmeter has infinite resistance so that it draws no current from the circuit.
12.3 Ohmmeter
An ohmmeter measures electrical resistance.
Resistance should generally be measured when the component is disconnected from an energized circuit.
12.4 Multimeter
A multimeter is an instrument that combines several measuring functions, commonly including:
- Voltage
- Current
- Resistance
- Continuity
Some digital multimeters also measure capacitance, frequency, temperature and other quantities.
13. Electrical Safety and Resistance
Resistance is important for electrical safety.
Electric shock occurs when electric current passes through the human body. Its effects depend on current magnitude, duration, path through the body and other conditions.
Electrical insulation helps prevent unwanted current flow.
Protective devices such as fuses and circuit breakers interrupt a circuit when current exceeds safe limits.
Wet conditions can increase the risk of electric shock because moisture and dissolved substances may reduce the effective resistance between the body and an electrical source.
14. Important Scientific Facts
- Current is the rate of flow of electric charge.
- The SI unit of current is the ampere.
- One ampere equals one coulomb per second.
- Voltage is measured in volts.
- Resistance is measured in ohms.
- Resistivity is measured in ohm metres.
- Conductance is measured in siemens.
- Electric power is measured in watts.
- Electrical energy is measured in joules or kilowatt-hours.
- An ammeter is connected in series.
- A voltmeter is connected in parallel.
- Conventional current in a metallic external circuit is opposite to electron flow.
- Batteries provide direct current, while electricity distribution networks commonly use alternating current.
15. Common Examination Pitfalls
- Current is the rate of flow of charge, not the amount of charge itself.
- One ampere equals one coulomb per second.
- Conventional current direction is opposite to electron flow in metals.
- Voltage is potential difference, not current.
- The SI unit of voltage is the volt.
- The SI unit of resistance is the ohm.
- Resistivity is measured in ohm metres, not ohms.
- Conductance is the reciprocal of resistance.
- An ammeter is connected in series, not parallel.
- A voltmeter is connected in parallel, not series.
- A kilowatt is a unit of power, while a kilowatt-hour is a unit of energy.
- The relationship (P=VI) gives real power directly in DC circuits and purely resistive AC circuits; general AC circuits require consideration of power factor.
36 Key Takeaways for Exams
- Electric current is the rate of flow of electric charge.
- Electric current is represented by the symbol (I).
- The SI unit of current is the ampere (A).
- One ampere equals one coulomb per second.
- Electric current is calculated using (I=Q/t) for steady current.
- Conventional current flows in the direction of positive charge movement.
- Electron flow in metallic conductors is opposite to conventional current.
- Direct current flows in one direction.
- Alternating current periodically changes direction.
- Frequency is the number of cycles per second.
- The SI unit of frequency is hertz (Hz).
- The time period is the reciprocal of frequency.
- Voltage is the electric potential difference between two points.
- Voltage represents the change in electric potential energy per unit charge.
- The SI unit of voltage is the volt (V).
- One volt equals one joule per coulomb.
- Electromotive force is energy supplied per unit charge by a source.
- EMF is measured in volts and is not a mechanical force.
- Terminal voltage may be lower than EMF when a source delivers current because of internal resistance.
- Electrical resistance opposes the flow of electric current.
- The SI unit of resistance is the ohm ((\Omega)).
- Resistance is given by (R=V/I) for an ohmic conductor.
- Resistance increases with conductor length.
- Resistance decreases with increasing cross-sectional area.
- Resistance depends on material and temperature.
- Resistivity is an intrinsic property of a material.
- The SI unit of resistivity is ohm metre ((\Omega m)).
- Conductance is the reciprocal of resistance.
- The SI unit of conductance is the siemens (S).
- Electric power is the rate of electrical energy transfer.
- Electrical power in a DC circuit is calculated using (P=VI).
- Other power expressions for an ohmic resistor are (P=I^2R) and (P=V^2/R).
- Electrical energy is calculated using (E=Pt).
- One kilowatt-hour equals (3.6\times10^6) joules.
- An ammeter is connected in series and an ideal ammeter has very low resistance.
- A voltmeter is connected in parallel and an ideal voltmeter has very high resistance.