Table of Contents
Ohm’s Law and Electrical Conductivity
1. Introduction
Ohm’s law is one of the fundamental principles of electrical science. It explains the relationship between voltage, electric current and resistance in an electrical conductor under specified physical conditions.
Electrical conductivity describes how easily a material allows electric current to pass through it. It is closely related to resistivity, which measures the opposition offered by a material to electric current.
These concepts are essential for understanding electrical circuits, wiring, electronic components, semiconductor devices and electrical power systems.
2. Ohm’s Law
Ohm’s law states that the electric current flowing through a conductor is directly proportional to the potential difference across it, provided its physical conditions, particularly temperature, remain constant.
Mathematically:
[
V\propto I
]
Therefore:
[
V=IR
]
Where:
- (V) = potential difference in volts (V)
- (I) = electric current in amperes (A)
- (R) = electrical resistance in ohms ((\Omega))
The resistance is constant for an ohmic conductor under the specified conditions.
2.1 Alternative Forms of Ohm’s Law
To calculate current:
[
I=\frac{V}{R}
]
To calculate resistance:
[
R=\frac{V}{I}
]
These equations are widely used in the analysis of simple electrical circuits.
Numerical Example 1: Calculating Current
A resistor of (10\ \Omega) is connected across a potential difference of (20\ V). Calculate the current.
[
I=\frac{V}{R}
]
[
I=\frac{20}{10}
]
[
\boxed{I=2\ A}
]
Numerical Example 2: Calculating Resistance
A current of (3\ A) flows through a conductor when a potential difference of (12\ V) is applied. Calculate its resistance.
[
R=\frac{V}{I}
]
[
R=\frac{12}{3}
]
[
\boxed{R=4\ \Omega}
]
3. Conditions for Ohm’s Law
Ohm’s law is valid for ohmic conductors when relevant physical conditions remain constant.
Important conditions include:
- Temperature should remain constant.
- The physical state of the conductor should not change.
- The conductor should operate within the range where its voltage-current relationship is linear.
Ohm’s law is not a universal law for every electrical component. Some devices have nonlinear voltage-current characteristics.
4. Ohmic and Non-Ohmic Conductors
4.1 Ohmic Conductors
Ohmic conductors obey Ohm’s law over the relevant operating range.
Their current is directly proportional to the applied voltage when physical conditions remain constant.
Examples include many ordinary metallic resistors operating within their specified limits.
4.2 Non-Ohmic Conductors and Devices
Non-ohmic devices do not maintain a constant ratio of voltage to current over their operating range.
Examples include:
- Semiconductor diodes
- Filament lamps
- Thermistors
- Many electronic components
Their resistance or current-voltage relationship changes with operating conditions.
5. Voltage-Current Graph
A voltage-current graph helps determine whether a conductor obeys Ohm’s law.
For an ohmic conductor, a graph of voltage on the vertical axis against current on the horizontal axis is a straight line passing through the origin.
The gradient is:
[
\text{Gradient}=\frac{\Delta V}{\Delta I}=R
]
If current is plotted on the vertical axis and voltage on the horizontal axis:
[
\text{Gradient}=\frac{\Delta I}{\Delta V}=\frac{1}{R}
]
The gradient therefore depends on which quantity is plotted on each axis.
Characteristics of an Ohmic V-I Graph
- It is a straight line.
- It passes through the origin.
- Its gradient is constant when voltage is plotted against current.
- The resistance remains constant under the specified conditions.
A curved voltage-current graph indicates a non-ohmic relationship over the measured range.
6. Resistance
Resistance is the opposition offered by a material or electrical component to the flow of electric current.
It is represented by (R).
[
R=\frac{V}{I}
]
The SI unit is the ohm ((\Omega)).
For a uniform conductor:
[
R=\rho\frac{L}{A}
]
Where:
- (R) = resistance
- (\rho) = resistivity
- (L) = conductor length
- (A) = cross-sectional area
Resistance increases with length and decreases with cross-sectional area, provided material and temperature remain unchanged.
7. Resistivity
Resistivity is an intrinsic electrical property of a material that indicates how strongly it opposes electric current.
It is represented by (\rho).
From the resistance equation:
[
R=\rho\frac{L}{A}
]
Rearranging:
[
\rho=\frac{RA}{L}
]
The SI unit of resistivity is ohm metre ((\Omega m)).
Characteristics of Resistivity
- It depends on the nature of the material.
- It generally changes with temperature.
- It does not directly depend on the dimensions of a uniform sample.
- Low resistivity materials are generally good electrical conductors.
- High resistivity materials are generally good electrical insulators.
Copper and silver have low resistivity, whereas rubber and glass have very high resistivity.
8. Electrical Conductivity
Electrical conductivity measures the ability of a material to conduct electric current.
It is represented by the Greek letter (\sigma).
Conductivity is the reciprocal of resistivity.
[
\sigma=\frac{1}{\rho}
]
The SI unit of electrical conductivity is siemens per metre (S/m).
A material with high conductivity allows electric current to flow easily, whereas a material with low conductivity offers greater opposition to current flow.
Relationship Between Conductivity and Resistivity
[
\rho=\frac{1}{\sigma}
]
[
\sigma=\frac{1}{\rho}
]
Therefore:
- High conductivity means low resistivity.
- Low conductivity means high resistivity.
9. Difference Between Resistance, Resistivity and Conductivity
| Property | Meaning | SI unit |
|---|---|---|
| Resistance | Opposition to current in a particular component | Ohm ((\Omega)) |
| Resistivity | Intrinsic opposition to current in a material | Ohm metre ((\Omega m)) |
| Conductivity | Ability of a material to conduct current | Siemens per metre (S/m) |
Resistance depends on material, dimensions and temperature. Resistivity and conductivity are material properties at a specified temperature and physical condition.
10. Factors Affecting Electrical Conductivity
10.1 Nature of Material
Different materials have different electrical conductivities because of differences in their atomic and electronic structures.
Metals generally have high conductivity because they contain mobile electrons.
10.2 Temperature
Temperature affects the electrical conductivity of materials.
In most metallic conductors, increasing temperature increases resistance and reduces conductivity.
In many semiconductors, increasing temperature increases the number of available charge carriers and can increase conductivity.
10.3 Impurities
Impurities can alter electrical conductivity.
In semiconductors, controlled addition of impurities, called doping, is used to increase and regulate conductivity.
10.4 Physical Structure
The composition, crystal structure, defects and other material characteristics can affect the movement of charge carriers.
11. Temperature Dependence of Resistance
The resistance of many metallic conductors increases approximately linearly with temperature over a limited temperature range.
A commonly used relationship is:
[
R_T=R_0[1+\alpha(T-T_0)]
]
Where:
- (R_T) = resistance at temperature (T)
- (R_0) = resistance at reference temperature (T_0)
- (\alpha) = temperature coefficient of resistance
For most pure metals, (\alpha) is positive over ordinary temperature ranges.
11.1 Positive Temperature Coefficient
A positive temperature coefficient means resistance increases as temperature rises.
Most ordinary metallic conductors show this behaviour.
11.2 Negative Temperature Coefficient
A negative temperature coefficient means resistance decreases as temperature rises.
Many semiconductor materials and thermistors designed with negative temperature coefficients show this behaviour.
12. Superconductivity
Superconductivity is a physical phenomenon in which certain materials exhibit zero DC electrical resistance below a characteristic critical temperature.
This phenomenon was first discovered in mercury by Heike Kamerlingh Onnes in 1911.
Important characteristics include:
- Zero DC electrical resistance in the superconducting state.
- Expulsion of magnetic flux from the bulk of an ideal superconductor under suitable conditions, known as the Meissner effect.
- A characteristic critical temperature.
- Strong dependence on magnetic field and current conditions.
Applications of Superconductivity
- Magnetic resonance imaging (MRI) systems.
- Particle accelerators.
- Magnetic levitation research and transport.
- Highly sensitive magnetic measurement devices.
- Advanced scientific and energy technologies.
Not all materials become superconducting, and superconductivity generally requires suitable temperature and operating conditions.
13. Semiconductor Conductivity
Semiconductors have electrical conductivity between that of conductors and insulators.
Their conductivity can be controlled through doping, temperature, light and applied electric fields.
13.1 Intrinsic Semiconductors
An intrinsic semiconductor is a chemically pure semiconductor without intentional doping.
Examples include pure silicon and germanium.
In an intrinsic semiconductor, electrons and holes are generated in equal numbers.
13.2 Extrinsic Semiconductors
An extrinsic semiconductor is a semiconductor whose conductivity is modified by adding controlled impurities.
There are two principal types.
N-type semiconductor
An N-type semiconductor is produced by doping a semiconductor with donor impurities that provide additional electrons.
Electrons are the majority charge carriers.
P-type semiconductor
A P-type semiconductor is produced by doping with acceptor impurities that create holes.
Holes are the majority charge carriers.
13.3 Applications
Semiconductor conductivity is essential to:
- Diodes
- Transistors
- Integrated circuits
- Solar cells
- Light-emitting diodes
- Computer processors
- Mobile phones
14. Electrical Power and Ohm’s Law
Electrical power is the rate at which electrical energy is transferred.
[
P=VI
]
Using Ohm’s law:
[
V=IR
]
Therefore:
[
P=I^2R
]
Also:
[
P=\frac{V^2}{R}
]
These equations are useful for calculating the power dissipated by an ohmic resistor.
Numerical Example
A resistor of (8\ \Omega) carries a current of (2\ A). Calculate the power dissipated.
[
P=I^2R
]
[
P=2^2\times8
]
[
P=4\times8
]
[
\boxed{P=32\ W}
]
15. Practical Applications of Ohm’s Law and Conductivity
15.1 Electrical Wiring
Conductive materials such as copper and aluminium are used in electrical wiring because of their relatively high conductivity.
15.2 Electrical Heating
Electric heaters use resistive elements to convert electrical energy into thermal energy.
15.3 Electronic Circuit Design
Ohm’s law is used to calculate appropriate resistor values and determine current and voltage in electronic circuits.
15.4 Semiconductor Technology
Controlled conductivity enables the operation of transistors, diodes, microprocessors and integrated circuits.
15.5 Electrical Power Systems
Resistance and conductivity calculations are essential for minimizing power losses in transmission and distribution systems.
16. Important Scientific Facts
- Ohm’s law is expressed as (V=IR).
- Ohm’s law applies to ohmic conductors under constant physical conditions.
- The voltage-current graph of an ohmic conductor is linear and passes through the origin.
- Resistivity is represented by (\rho).
- Conductivity is represented by (\sigma).
- Conductivity is the reciprocal of resistivity.
- The SI unit of resistivity is (\Omega m).
- The SI unit of conductivity is S/m.
- Metals generally have positive temperature coefficients of resistance.
- Many semiconductor materials show increasing conductivity with increasing temperature.
- Superconductors exhibit zero DC electrical resistance below their critical temperature in the superconducting state.
17. Common Examination Pitfalls
- Ohm’s law does not apply universally to all electrical devices.
- Temperature and other relevant physical conditions must remain constant for the ordinary linear Ohm’s law relationship.
- If voltage is on the vertical axis and current on the horizontal axis, the graph’s gradient equals resistance.
- If current is on the vertical axis and voltage on the horizontal axis, the gradient equals conductance.
- Resistance and resistivity are not the same quantity.
- Resistivity is measured in (\Omega m), not (\Omega).
- Conductivity is measured in S/m, not S.
- Conductivity is inversely proportional to resistivity.
- Most metals have resistance that increases with temperature.
- Many semiconductors have conductivity that increases with temperature.
- A diode is a common example of a non-ohmic device.
- Superconductivity is associated with zero DC resistance below a critical temperature, not simply low resistance at room temperature.
36 Key Takeaways for Exams
- Ohm’s law describes the relationship between voltage, current and resistance.
- Ohm’s law states that current is directly proportional to voltage when relevant physical conditions remain constant.
- The mathematical expression of Ohm’s law is (V=IR).
- Voltage is measured in volts.
- Current is measured in amperes.
- Resistance is measured in ohms.
- Current can be calculated using (I=V/R).
- Resistance can be calculated using (R=V/I).
- Ohm’s law is valid for ohmic conductors under specified conditions.
- Temperature is an important physical condition affecting resistance.
- Ohmic conductors have a linear voltage-current relationship.
- The voltage-current graph of an ohmic conductor passes through the origin.
- When voltage is plotted against current, the gradient equals resistance.
- When current is plotted against voltage, the gradient equals conductance.
- Non-ohmic devices have nonlinear voltage-current characteristics over relevant operating ranges.
- A semiconductor diode is an example of a non-ohmic device.
- Resistance is the opposition offered to electric current.
- Resistance depends on material, length, cross-sectional area and temperature.
- Resistance of a uniform conductor is given by (R=\rho L/A).
- Resistivity is an intrinsic property of a material.
- Resistivity is represented by the symbol (\rho).
- The SI unit of resistivity is ohm metre ((\Omega m)).
- Electrical conductivity measures the ability of a material to conduct current.
- Conductivity is represented by the symbol (\sigma).
- Conductivity is the reciprocal of resistivity.
- The SI unit of conductivity is siemens per metre (S/m).
- High conductivity corresponds to low resistivity.
- Most metals have a positive temperature coefficient of resistance.
- Many semiconductor materials exhibit increasing conductivity as temperature rises.
- Doping is used to control semiconductor conductivity.
- N-type semiconductors have electrons as majority charge carriers.
- P-type semiconductors have holes as majority charge carriers.
- Superconductivity is a phenomenon in which certain materials exhibit zero DC resistance below a critical temperature.
- The Meissner effect describes the expulsion of magnetic flux from the bulk of a superconductor under suitable conditions.
- Electrical power in an ohmic resistor can be calculated using (P=VI), (P=I^2R) or (P=V^2/R).
- Ohm’s law and electrical conductivity are fundamental to electrical engineering, electronics, wiring and modern semiconductor technology.