General Science – Physics – Series and Parallel Electrical Circuits

Series and Parallel Electrical Circuits

1. Introduction

An electrical circuit is a closed conducting path through which electric current can flow.

Electrical circuits contain components such as power sources, connecting wires, switches, resistors, lamps, motors and electronic devices.

Two fundamental methods of connecting electrical components are:

  1. Series connection
  2. Parallel connection

The arrangement of components determines how current and voltage are distributed throughout a circuit.

Understanding series and parallel circuits is essential for studying household wiring, electrical appliances, electronic systems and power distribution.

2. Basic Components of an Electrical Circuit

2.1 Power Source

A power source supplies electrical energy to a circuit.

Examples include:

  • Batteries
  • Electric cells
  • Generators
  • DC power supplies

2.2 Conducting Wires

Conducting wires connect the components and provide a path for electric current.

Copper and aluminium are commonly used because of their relatively high electrical conductivity.

2.3 Switch

A switch controls whether the circuit is open or closed.

  • A closed switch completes the circuit and allows current to flow.
  • An open switch breaks the circuit and interrupts current flow.

2.4 Load

A load is a component that consumes or converts electrical energy.

Examples include:

  • Electric bulbs
  • Heaters
  • Motors
  • Fans
  • Electronic devices

2.5 Resistor

A resistor is a component designed to provide a specified resistance in an electrical circuit.

It is used to control current, divide voltage and protect sensitive electronic components.

3. Open and Closed Circuits

3.1 Closed Circuit

A closed circuit provides a complete conducting path through which electric current can flow.

3.2 Open Circuit

An open circuit contains a break in the conducting path, preventing sustained current flow.

3.3 Short Circuit

A short circuit occurs when an unintended low-resistance path allows excessive current to flow.

It may cause:

  • Overheating
  • Damage to electrical equipment
  • Fire hazards
  • Failure of electrical components

Fuses and circuit breakers help protect circuits against dangerous overcurrent conditions.

4. Series Circuits

A series circuit is an electrical circuit in which components are connected along a single conducting path.

The same current flows through every component because there is only one path for the current.

4.1 Characteristics of Series Circuits

  1. The same current flows through all components.
  2. The supply voltage is divided among the components.
  3. Total resistance equals the sum of individual resistances.
  4. Adding another resistor increases total resistance.
  5. If one component breaks or is disconnected, the entire circuit path is interrupted.

4.2 Equivalent Resistance in a Series Circuit

For resistors connected in series:

[
R_s=R_1+R_2+R_3+\cdots+R_n
]

Where:

  • (R_s) = equivalent series resistance
  • (R_1,R_2,R_3) = individual resistances

The total series resistance is greater than any individual positive resistance in the combination.

Numerical Example 1: Series Resistance

Three resistors of (2\ \Omega), (4\ \Omega) and (6\ \Omega) are connected in series. Calculate the equivalent resistance.

[
R_s=R_1+R_2+R_3
]

[
R_s=2+4+6
]

[
\boxed{R_s=12\ \Omega}
]

If a (24\ V) supply is connected across the combination, the total current is:

[
I=\frac{V}{R_s}
]

[
I=\frac{24}{12}
]

[
\boxed{I=2\ A}
]

4.3 Voltage Division in Series Circuits

In a series circuit, the total voltage is divided among the components.

According to Kirchhoff’s voltage law:

[
V=V_1+V_2+V_3+\cdots
]

For resistors connected in series, the voltage across each resistor is proportional to its resistance when the same current flows through all of them.

[
V_n=IR_n
]

A larger resistance receives a larger share of the total voltage.

Numerical Example 2: Voltage Division

Two resistors of (4\ \Omega) and (8\ \Omega) are connected in series across a (24\ V) supply.

First, calculate total resistance:

[
R_s=4+8=12\ \Omega
]

Total current:

[
I=\frac{24}{12}=2\ A
]

Voltage across the first resistor:

[
V_1=IR_1=2\times4=8\ V
]

Voltage across the second resistor:

[
V_2=IR_2=2\times8=16\ V
]

Check:

[
V_1+V_2=8+16=24\ V
]

The total voltage is correctly divided.

5. Parallel Circuits

A parallel circuit is an electrical circuit in which components are connected across the same two electrical nodes, creating multiple current paths.

5.1 Characteristics of Parallel Circuits

  1. The same voltage exists across each parallel branch.
  2. Current divides among the different branches.
  3. Total current equals the sum of the branch currents.
  4. Equivalent resistance is less than the resistance of the smallest individual branch, for positive finite resistances.
  5. If one branch is disconnected, the other branches can continue operating.

5.2 Equivalent Resistance in a Parallel Circuit

For resistors connected in parallel:

[
\frac{1}{R_p}=
\frac{1}{R_1}+
\frac{1}{R_2}+
\frac{1}{R_3}+\cdots
]

For two resistors in parallel:

[
R_p=\frac{R_1R_2}{R_1+R_2}
]

Where:

  • (R_p) = equivalent parallel resistance
  • (R_1,R_2) = individual resistances

Numerical Example 3: Parallel Resistance

Two resistors of (6\ \Omega) and (3\ \Omega) are connected in parallel. Calculate their equivalent resistance.

[
R_p=\frac{R_1R_2}{R_1+R_2}
]

[
R_p=\frac{6\times3}{6+3}
]

[
R_p=\frac{18}{9}
]

[
\boxed{R_p=2\ \Omega}
]

The equivalent resistance is lower than either individual resistance.

5.3 Current Division in Parallel Circuits

In a parallel circuit, the total current divides among the branches.

[
I=I_1+I_2+I_3+\cdots
]

The voltage across every branch is the same.

Using Ohm’s law:

[
I_1=\frac{V}{R_1}
]

[
I_2=\frac{V}{R_2}
]

The branch with lower resistance carries greater current.

Numerical Example 4: Current Division

Two resistors of (4\ \Omega) and (8\ \Omega) are connected in parallel across a (16\ V) supply.

Current through the first resistor:

[
I_1=\frac{16}{4}=4\ A
]

Current through the second resistor:

[
I_2=\frac{16}{8}=2\ A
]

Total current:

[
I=I_1+I_2
]

[
I=4+2
]

[
\boxed{I=6\ A}
]

Equivalent resistance:

[
R_p=\frac{16}{6}
]

[
\boxed{R_p\approx2.67\ \Omega}
]

6. Difference Between Series and Parallel Circuits

Feature Series circuit Parallel circuit
Current Same through all components Divides among branches
Voltage Divided among components Same across each branch
Current paths One Multiple
Equivalent resistance Sum of resistances Reciprocal sum
Adding resistance Increases total resistance Usually decreases equivalent resistance
Component failure Can interrupt the whole circuit Other branches can continue operating
Common application Some decorative light strings and simple resistor networks Household wiring and many distribution systems

7. Kirchhoff’s Laws

Kirchhoff’s laws are fundamental principles used to analyse electrical circuits.

There are two main laws:

  1. Kirchhoff’s current law (KCL)
  2. Kirchhoff’s voltage law (KVL)

7.1 Kirchhoff’s Current Law

Kirchhoff’s current law states that the total current entering a junction equals the total current leaving the junction.

[
\sum I_{\text{in}}=\sum I_{\text{out}}
]

It is based on the conservation of electric charge.

For example, if (5\ A) enters a junction and two outgoing branches carry (2\ A) and (I), then:

[
5=2+I
]

[
\boxed{I=3\ A}
]

7.2 Kirchhoff’s Voltage Law

Kirchhoff’s voltage law states that the algebraic sum of all potential differences around any closed loop in a circuit is zero.

[
\sum V=0
]

It is based on the conservation of energy.

For a simple circuit containing a battery and resistors:

[
\varepsilon-V_1-V_2=0
]

Therefore:

[
\varepsilon=V_1+V_2
]

The energy supplied by the source is equal to the energy transferred or dissipated in the circuit elements around the loop.

8. Combined Series and Parallel Circuits

Many practical electrical circuits contain both series and parallel connections.

Such circuits are analysed by simplifying one section at a time.

Numerical Example 5: Combined Circuit

A (4\ \Omega) resistor is connected in series with a parallel combination of (6\ \Omega) and (3\ \Omega) resistors. The circuit is connected to a (24\ V) source.

Step 1: Calculate parallel resistance.

[
R_p=\frac{6\times3}{6+3}
]

[
R_p=2\ \Omega
]

Step 2: Calculate total resistance.

[
R_T=4+2
]

[
R_T=6\ \Omega
]

Step 3: Calculate total current.

[
I=\frac{V}{R_T}
]

[
I=\frac{24}{6}
]

[
\boxed{I=4\ A}
]

Step 4: Calculate voltage across the series resistor.

[
V_1=IR_1
]

[
V_1=4\times4=16\ V
]

Step 5: Calculate voltage across the parallel section.

[
V_p=24-16=8\ V
]

Step 6: Calculate branch currents.

Through the (6\ \Omega) resistor:

[
I_1=\frac{8}{6}=1.33\ A
]

Through the (3\ \Omega) resistor:

[
I_2=\frac{8}{3}=2.67\ A
]

Check:

[
I_1+I_2=1.33+2.67=4\ A
]

The branch currents add up to the total current.

9. Household Electrical Wiring

Most household electrical appliances are connected in parallel.

This arrangement provides several advantages:

  1. Each appliance receives approximately the same supply voltage.
  2. Appliances can be switched on and off independently.
  3. Failure of one appliance does not normally interrupt the operation of other appliances.
  4. Each appliance draws current according to its own electrical characteristics.

In a typical household distribution arrangement, protective devices such as fuses and circuit breakers help prevent dangerous overcurrent conditions.

9.1 Fuse

A fuse is a protective device containing a conducting element designed to melt when excessive current flows through it for a sufficient period.

It interrupts the circuit and helps protect wiring and equipment.

9.2 Circuit Breaker

A circuit breaker is an automatic switching device that interrupts current when specified fault or overload conditions occur.

Unlike a conventional fuse, many circuit breakers can be reset after the fault has been corrected.

9.3 Earthing

Earthing provides a protective connection between exposed conductive parts of electrical equipment and the Earth through an appropriate protective conductor.

It helps reduce the risk of electric shock by providing a path for fault current and supporting the operation of protective devices.

10. Electrical Power in Series and Parallel Circuits

Electrical power is calculated using:

[
P=VI
]

For an ohmic resistor:

[
P=I^2R
]

Or:

[
P=\frac{V^2}{R}
]

10.1 Power in Series Circuits

The same current flows through every series component.

Therefore, the power consumed by each resistor is:

[
P_n=I^2R_n
]

A resistor with greater resistance dissipates more power when the same current passes through it.

10.2 Power in Parallel Circuits

The same voltage is applied across each parallel branch.

Therefore:

[
P_n=\frac{V^2}{R_n}
]

A branch with lower resistance draws more current and dissipates more power under the same applied voltage.

11. Practical Applications of Series and Parallel Circuits

11.1 Household Electrical Systems

Household appliances are generally connected in parallel so that they can operate independently.

11.2 Decorative Lighting

Some decorative light arrangements use series connections, although many modern designs use more complex configurations.

11.3 Batteries

Battery cells can be connected in series to increase total voltage.

Cells can also be connected in parallel to increase available capacity or current capability, subject to proper design and matching.

11.4 Electronic Circuits

Series and parallel resistor combinations are widely used in voltage dividers, current-limiting circuits, sensors and electronic devices.

11.5 Power Distribution

Parallel arrangements allow electrical loads to receive supply voltage through separate branches.

12. Important Scientific Facts

  • A series circuit has a single current path.
  • A parallel circuit has multiple current paths.
  • Current is the same through all components in a series circuit.
  • Voltage is the same across all branches of a parallel circuit.
  • Series resistance is the sum of individual resistances.
  • Parallel resistance is calculated through the reciprocal relationship.
  • The equivalent resistance of a parallel combination is lower than its smallest individual positive resistance.
  • Kirchhoff’s current law is based on conservation of charge.
  • Kirchhoff’s voltage law is based on conservation of energy.
  • Household appliances are generally connected in parallel.
  • Fuses and circuit breakers provide protection against overcurrent conditions.

13. Common Examination Pitfalls

  1. In a series circuit, current is the same through all components, not voltage.
  2. In a parallel circuit, voltage is the same across branches, not current.
  3. Series resistance is calculated by direct addition.
  4. Parallel resistance is calculated by adding reciprocals.
  5. Equivalent resistance in a parallel circuit is lower than the smallest branch resistance for positive finite resistors.
  6. If one component breaks in a simple series circuit, the entire circuit is interrupted.
  7. Failure of one parallel branch does not necessarily stop the other branches.
  8. Kirchhoff’s current law is based on conservation of charge.
  9. Kirchhoff’s voltage law is based on conservation of energy.
  10. Household appliances are generally connected in parallel.
  11. A fuse is designed to interrupt excessive current.
  12. A short circuit creates an unintended low-resistance path and may cause dangerous current.

36 Key Takeaways for Exams

  1. An electrical circuit is a closed conducting path through which current can flow.
  2. A power source supplies electrical energy to a circuit.
  3. A load converts electrical energy into another form of energy.
  4. A switch controls the completion or interruption of a circuit.
  5. A closed circuit provides a complete path for current.
  6. An open circuit contains a break in the conducting path.
  7. A short circuit creates an unintended low-resistance path.
  8. A series circuit has only one conducting path.
  9. A parallel circuit contains multiple conducting paths.
  10. The same current flows through all components in a series circuit.
  11. Voltage is divided among components in a series circuit.
  12. Equivalent series resistance is the sum of individual resistances.
  13. Series resistance is expressed as (R_s=R_1+R_2+\cdots).
  14. Adding a resistor in series increases total resistance.
  15. Failure of one component can interrupt an entire simple series circuit.
  16. In a parallel circuit, the voltage across every branch is the same.
  17. Current divides among parallel branches.
  18. Total current in a parallel circuit equals the sum of branch currents.
  19. Parallel resistance is calculated using the reciprocal-sum formula.
  20. For two parallel resistors, (R_p=R_1R_2/(R_1+R_2)).
  21. Equivalent parallel resistance is lower than the smallest individual positive resistance.
  22. A lower-resistance parallel branch carries more current at the same voltage.
  23. Household appliances are generally connected in parallel.
  24. Parallel connections allow appliances to operate independently.
  25. Kirchhoff’s current law states that total current entering a junction equals total current leaving it.
  26. Kirchhoff’s current law is based on conservation of electric charge.
  27. Kirchhoff’s voltage law states that the algebraic sum of potential differences around a closed loop is zero.
  28. Kirchhoff’s voltage law is based on conservation of energy.
  29. Combined circuits contain both series and parallel connections.
  30. A combined circuit can be simplified by calculating equivalent resistance section by section.
  31. Electrical power is calculated using (P=VI).
  32. Power in an ohmic resistor can also be calculated using (P=I^2R) or (P=V^2/R).
  33. A fuse interrupts a circuit when excessive current causes its conducting element to melt.
  34. A circuit breaker automatically interrupts current under specified fault or overload conditions.
  35. Earthing provides a protective path for fault current and supports electrical safety.
  36. Series and parallel circuits are fundamental to household wiring, electronic systems, batteries and electrical power distribution.
7 Views