Table of Contents
Thermal Efficiency and Heat Engines
Multiple-Choice Questions
1 A heat engine is a device that converts:
(a) Mechanical work into heat only
(b) Heat energy into mechanical work
(c) Electrical energy into chemical energy
(d) None of these
2 A conventional heat engine operates between:
(a) A hot reservoir and a cold reservoir
(b) Two reservoirs at absolute zero
(c) Two reservoirs at identical temperatures
(d) None of these
3 The hot reservoir of a heat engine is also called the:
(a) Heat sink
(b) Condenser
(c) Heat source
(d) None of these
4 The cold reservoir of a heat engine is commonly called the:
(a) Heat source
(b) Heat sink
(c) Combustion chamber
(d) None of these
5 Thermal efficiency is defined as the ratio of:
(a) Heat rejected to heat absorbed
(b) Work input to heat output
(c) Useful work output to heat input
(d) None of these
6 The thermal efficiency of a heat engine is:
(a) η = Wout/Qin
(b) η = Qin/Wout
(c) η = Qout/Wout
(d) None of these
7 For a cyclic heat engine, the net work output is equal to:
(a) Heat rejected alone
(b) Heat absorbed minus heat rejected
(c) Heat absorbed plus heat rejected
(d) None of these
8 If a heat engine absorbs 1,000 J of heat and produces 300 J of work, its efficiency is:
(a) 20%
(b) 50%
(c) 30%
(d) None of these
9 A heat engine absorbs 2,000 J of heat and rejects 1,200 J. Its work output is:
(a) 800 J
(b) 1,200 J
(c) 3,200 J
(d) None of these
10 A heat engine converts 40% of its heat input into work. If it absorbs 5,000 J, its work output is:
(a) 1,000 J
(b) 2,000 J
(c) 3,000 J
(d) None of these
11 The maximum possible efficiency of an ideal heat engine operating between two thermal reservoirs is given by:
(a) Boyle’s law
(b) Charles’s law
(c) Carnot efficiency
(d) None of these
12 The efficiency of a Carnot engine depends on:
(a) The temperatures of the hot and cold reservoirs
(b) The mass of the working substance only
(c) The shape of the engine
(d) None of these
13 The Carnot efficiency is expressed as:
(a) η = Th/Tc
(b) η = 1 − Tc/Th
(c) η = Tc/Th
(d) None of these
14 In the Carnot efficiency equation, temperatures must be expressed in:
(a) Celsius
(b) Fahrenheit
(c) Kelvin
(d) None of these
15 A Carnot engine operates between 600 K and 300 K. Its maximum theoretical efficiency is:
(a) 50%
(b) 25%
(c) 75%
(d) None of these
16 A Carnot engine operates between 800 K and 400 K. Its efficiency is:
(a) 25%
(b) 50%
(c) 75%
(d) None of these
17 If the temperature of the cold reservoir decreases while the hot reservoir temperature remains constant, Carnot efficiency:
(a) Decreases
(b) Remains unchanged
(c) Increases
(d) None of these
18 If the hot reservoir temperature increases while the cold reservoir temperature remains constant, Carnot efficiency:
(a) Increases
(b) Decreases
(c) Becomes zero
(d) None of these
19 A heat engine operating between reservoirs at the same temperature has a maximum theoretical efficiency of:
(a) 100%
(b) 50%
(c) 25%
(d) None of these
20 Which statement about a real heat engine is correct?
(a) It can be more efficient than a Carnot engine operating between the same temperatures
(b) It is always 100% efficient
(c) Its efficiency is lower than the corresponding Carnot efficiency
(d) None of these
21 Which of the following is an example of a heat engine?
(a) Electric heater
(b) Internal combustion engine
(c) Electric resistance cooker
(d) None of these
22 In a four-stroke petrol engine, the stroke that draws the air-fuel mixture into the cylinder is called:
(a) Intake stroke
(b) Compression stroke
(c) Power stroke
(d) None of these
23 In a four-stroke petrol engine, the air-fuel mixture is ignited by:
(a) Compression alone
(b) An electric spark
(c) Exhaust gases
(d) None of these
24 In a conventional diesel engine, ignition occurs primarily due to:
(a) A spark plug
(b) An external flame
(c) High-temperature compressed air
(d) None of these
25 Which component in an internal combustion engine converts the reciprocating motion of the piston into rotary motion?
(a) Crankshaft
(b) Carburettor
(c) Radiator
(d) None of these
26 The main function of a condenser in a steam power plant is to:
(a) Increase steam pressure continuously
(b) Convert exhaust steam into water
(c) Burn the fuel
(d) None of these
27 Which thermodynamic cycle is an ideal model for a petrol spark-ignition engine?
(a) Rankine cycle
(b) Diesel cycle
(c) Otto cycle
(d) None of these
28 Which thermodynamic cycle is an ideal model for a compression-ignition diesel engine?
(a) Otto cycle
(b) Diesel cycle
(c) Carnot refrigeration cycle
(d) None of these
29 The ideal cycle commonly used to model steam power plants is:
(a) Rankine cycle
(b) Otto cycle
(c) Diesel cycle
(d) None of these
30 In a steam power plant, the boiler primarily:
(a) Condenses exhaust steam
(b) Converts steam into liquid water
(c) Adds heat to water to produce steam
(d) None of these
31 The turbine in a steam power plant converts:
(a) Mechanical energy into chemical energy
(b) Thermal energy of steam into mechanical work
(c) Electrical energy into heat
(d) None of these
32 Which device converts the mechanical rotation of a turbine into electrical energy?
(a) Generator
(b) Condenser
(c) Boiler
(d) None of these
33 A refrigerator is best described as a device that:
(a) Produces cold without energy input
(b) Converts all heat into work
(c) Transfers heat from a low-temperature region to a high-temperature region using work
(d) None of these
34 The coefficient of performance of a refrigerator is:
(a) Work input divided by heat removed from the cold space
(b) Heat removed from the cold space divided by work input
(c) Heat rejected divided by work input
(d) None of these
35 A refrigerator removes 600 J of heat from its cold compartment using 200 J of work. Its coefficient of performance is:
(a) 3
(b) 2
(c) 4
(d) None of these
36 A heat pump is designed primarily to:
(a) Remove heat from a cold space only
(b) Convert heat completely into work
(c) Deliver heat to a warm space
(d) None of these
37 The coefficient of performance of a heat pump is:
(a) Work input divided by heat delivered
(b) Heat delivered to the warm space divided by work input
(c) Heat removed from the cold space divided by heat delivered
(d) None of these
38 For the same operating conditions, the coefficient of performance of a heat pump is:
(a) One greater than the coefficient of performance of the corresponding refrigerator
(b) Always zero
(c) Always less than that of the refrigerator
(d) None of these
39 Which of the following is a limitation of a heat engine?
(a) It cannot transfer energy
(b) It cannot produce mechanical work
(c) It cannot convert all absorbed heat into work in a cyclic operation
(d) None of these
40 The second law of thermodynamics places a limit on:
(a) The maximum possible efficiency of heat engines
(b) The conservation of mass
(c) The value of gravitational acceleration
(d) None of these
41 A heat engine absorbs 4,000 J of heat and rejects 2,500 J. Its work output is:
(a) 1,000 J
(b) 1,500 J
(c) 2,500 J
(d) None of these
42 A heat engine has an efficiency of 25% and produces 500 J of work. The heat input is:
(a) 1,000 J
(b) 1,500 J
(c) 2,000 J
(d) None of these
43 A Carnot engine operates between 500 K and 250 K. Its efficiency is:
(a) 50%
(b) 25%
(c) 75%
(d) None of these
44 Which process in a Carnot cycle occurs at constant temperature?
(a) Isothermal process
(b) Isochoric process
(c) Isobaric process
(d) None of these
45 The ideal Carnot cycle consists of:
(a) Two isobaric and two isochoric processes
(b) Two isothermal and two adiabatic processes
(c) Four isochoric processes
(d) None of these
46 Which statement about the Carnot engine is correct?
(a) Its efficiency depends on the working substance
(b) It operates with no heat rejection
(c) Its efficiency depends only on the temperatures of the two reservoirs
(d) None of these
47 The waste heat rejected by a thermal power plant is mainly associated with:
(a) The unavoidable thermodynamic limitations of energy conversion
(b) Complete conversion of heat into work
(c) The creation of additional energy
(d) None of these
48 Which of the following is a method of improving the practical efficiency of a thermal power plant?
(a) Increasing friction in moving components
(b) Reducing unnecessary heat losses and improving cycle performance
(c) Increasing heat rejection without improving output
(d) None of these
49 A heat engine absorbs 10,000 J of heat and rejects 7,000 J. Its thermal efficiency is:
(a) 30%
(b) 50%
(c) 70%
(d) None of these
50 Which statement correctly describes the relationship between a heat engine and the second law of thermodynamics?
(a) A cyclic heat engine can convert all heat from a single reservoir into work
(b) A real heat engine must reject some heat, and its efficiency is limited
(c) A heat engine can operate without any energy input
(d) None of these
Answer Key
1 (b) Heat energy into mechanical work
2 (a) A hot reservoir and a cold reservoir
3 (c) Heat source
4 (b) Heat sink
5 (c) Useful work output to heat input
6 (a) η = Wout/Qin
7 (b) Heat absorbed minus heat rejected
8 (c) 30%
9 (a) 800 J
10 (b) 2,000 J
11 (c) Carnot efficiency
12 (a) Temperatures of the hot and cold reservoirs
13 (b) η = 1 − Tc/Th
14 (c) Kelvin
15 (a) 50%
16 (b) 50%
17 (c) Increases
18 (a) Increases
19 (d) None of these
20 (c) Lower than the corresponding Carnot efficiency
21 (b) Internal combustion engine
22 (a) Intake stroke
23 (b) An electric spark
24 (c) High-temperature compressed air
25 (a) Crankshaft
26 (b) Convert exhaust steam into water
27 (c) Otto cycle
28 (b) Diesel cycle
29 (a) Rankine cycle
30 (c) Adds heat to water to produce steam
31 (b) Thermal energy of steam into mechanical work
32 (a) Generator
33 (c) Transfers heat from a low-temperature region to a high-temperature region using work
34 (b) Heat removed from the cold space divided by work input
35 (a) 3
36 (c) Deliver heat to a warm space
37 (b) Heat delivered to the warm space divided by work input
38 (a) One greater than the refrigerator’s coefficient of performance
39 (c) Cannot convert all absorbed heat into work in a cycle
40 (a) Maximum possible efficiency of heat engines
41 (b) 1,500 J
42 (c) 2,000 J
43 (a) 50%
44 (a) Isothermal process
45 (b) Two isothermal and two adiabatic processes
46 (c) Depends only on reservoir temperatures
47 (a) Thermodynamic limitations of energy conversion
48 (b) Reducing unnecessary heat losses and improving cycle performance
49 (a) 30%
50 (b) A real heat engine must reject some heat, and its efficiency is limited